Suzhou East-Sea Filter Equipment Co., Ltd.
 Automobiles & Motorcycles > Auto Engine >  Recycled PET Bottle Flake Chip Spinning Non-Woven( PET-- Non-WovenF), Spinning Machinery, Textile Machinery

Recycled PET Bottle Flake Chip Spinning Non-Woven( PET-- Non-WovenF), Spinning Machinery, Textile Machinery

Brand Name:
East-Sea
Spinning Method:
Rotor Spinning
Automatic:
Yes
Condition:
New
Spinning line:
Non-Woven
Port::
Shanghai
Recycled PET Bottle Flake Chip Spinning Non-Woven( PET-- Non-WovenF), Spinning Machinery, Textile Machinery
 
Detailed Description
 


1 High-Tech Recycled PET for Spinning Non-Woven
2 Spinning Machinery, Textile Machinery
3 Material Cost saving by 40% -50%

 Recycled PET Bottle Flake Chip Spinning PSF ( PET-- Non-Woven), Spinning Machinery, Textile Machinery

Brief Introduction of Modification for Regenerated Bottle Flake Chip Spinning

 

 

Commercial value: cost of chip-into-bottle flake engineering and benefit after modification.

Modification base: original chip product line which forms chip suitable for spinning, and market for bottle flakes.

 

Engineering modification: modifications of equipment, automatic control and construction (see detailed interpretations).

 

Technique modification: adjustments on conveyer (see detailed interpretations), crystallization, drying, temperature of screw rods and spinning, oiling (see detailed interpretations) and other technical parameters.

Operation management adjustment: material sources, operators and supplies replacement.

 

Specification of the engineering modification: 

Chips for spinning are different from the bottle flakes in many aspects, and compassions of their main parameters are shown in the table

 

Item

Chip

Bottle flake

Viscosity  (iv) 

0.64~0.66

0.74~0.76

Viscosity deviation

±0.01

±0.03

Melting point(°C) 

≥260

≥248

Water content of wet chip/bottle flake %

≤0.4

≤1.0

 

The chips and bottle flakes shall be treated by different equipment systems because of their different physical properties. The bottle flakes are about half the chips in bulk density, and the wet bottle flakes contain more water, so pre-crystallizer and drying tower for treating the bottle flakes shall be larger than these for chips so as to ensure enough pre-crystallizing and drying times. The bottle flakes are larger than the chips in viscosity, so screw rods shall be replaced by deep-slotted screws for uniformly melting and plasticizing the bottle flakes. And a double filter is needed for treating the bottle flakes which contain a lot of impurities.


1. Modification of drying system: The drying system for the bottle flakes is very different from that for the chips because of great differences in bulk density, shape and particles liquidity of them. The yield will be halved and conveyer, conveying pipes, fluidized bed and drying tower must be completed reformed if the modification is carried out on the basis of the drying system for the chips. Besides, an overall modification is needed for conveyer, transmission pipe, fluidized bed and internal drying tower, which requires a high cost. Moreover, the modification cannot bring satisfactory drying effect. So, to buy special drying equipment for the bottle flakes is suggested.  

 

2. Modification of screw rods: on the basis of the original screw rods host, sleeves of the original screw rods shall be maintained and the screw rods shall be replaced by deep-slotted screw rods.

 

3. Filter: Single-stage filter is sufficient for the chips because the chips contain few impurities. But the bottle flakes with plenty of impurities need to be filtered twice with a booster pump which is used for making up large pressure reduced after filtering. So the single-stage filter must be replaced by a double filter with a booster pump.

 

Adjustments in construction, public works, pipe and electricity supply corresponding to the modifications of the equipment shall be carried out.

 

Construction modification: The modifications of the equipment definitely lead to modifications of construction. Volumes of the fluidized bed and drying tower, corresponding preformed holes and equipment load shall be increased, which needs local changes to the construction. The double filter is much larger than the single-stage filter, so the screw rods and filter shall be rearranged if the original space is too small. In addition, steel beams shall be equipped under floor slabs to support increased equipment load. 

 

Public works: Compressed air consumption for drying the bottle flake is 50-70% larger than that for the chips. The former air compressing system can be used if it is capable, or additional air compressors are needed.

 

Pipe: A pipe for delivering compressed air to the drying equipment, a pipe for delivering biphenyl to the filter and a pipe for delivering cooling water to the screw rods (when the screw rods are rearranged) shall be modified.

 

Electricity supply: The new power load shall be at most 5% higher than the original one, so usually the original transformer can be used continuously. But if many are modified, replacement or addition of transformers needs to be considered.


We promise to supply you with high quality Spinning Line-- Recycled PET Bottle Flake Spinning!Of course , if you have some good ideas that you want us to develop or reproduced, please feel free to send us your product image or design artwork, we are also pleased to become your Original Equipment Manufacture.We promise you with the finest price,high quality and best service.We are sincerely looking for your cooperation!


Company information:
    Suzhou East-Sea Filter Equipment Co., Ltd. ,established in 2003 . We is an exporter of China (Mainland) Auto Filter products.    With independent export rights, our products have been exported to North America South America Eastern Europe Southeast Asia Africa Mid East, etc. The aim we pursue is to be the best in quality & price, and we always have been devoted to our customers for their requirements!    We take this opportunity to invite you to become our partner!Welcome to visit our company website(www.eastseafilter.com), if you have interest of any of our product, please let us know. We will be happy to give you a quotation upon receipt of your detailed requirements
Hot Searches: Plastic Drinking Straw Making Machine ,Used Drinking Straw Machine ,Straw Machin ,Drinking Straws Machinery ,Straws Machine
 
Send Inquiry to this Supplier
 
Suzhou East-Sea Filter Equipment Co., Ltd.
Ms. Jing Ling
No. 555 East Zhenxin Rd., Zhangpu Town
86-138-06260237

Copyright © 2010 Wholesale lots. All rights reserved. Contact Us:tonyluo2005@gmail.com

Processed in 0.12069 second(s)