Shenzhen Rhymestar Technology Co., Ltd.

Rebar Tying tool

Brand Name:
Rstar
Model Number:
RT-4089
Power Source:
Electricity
Model Number:
RT-4089
Rebar:
Rebar Tier
Place of Origin:
Guangdong, China
Rebar Tying tool
 
Detailed Description
 


Rebar Tying, Rebar Tier. Hand-held Automatic Rebar Tying machine can tie the rebar automatically and quickly by itself.

Rebar Tying, Rebar Tier.

Product Name:  Hand-held Automatic Rebar Tying Machine

Model No.: RT-4088

Product Descriptions:

Working Voltage: 9.6V

Maximum Tying Diameter: 40 mm

Tying Speed Per Knot: 0.8 Second

Wire Length of Per Knot: 500 mm (2 wraps) / 700 mm (3 wraps)

Tying Knots (in full charge): 1100 - 1200 knots

Wire Diameter: 0.8 mm

Wire Material: Annealed wire (Q195 / ZS08)

Wire Length of Per Spool: 95,000 mm

Tying Knots of One Spool: 190 Knots

Weight of One Spool: 0.4 kgs

Battery Capacity: 2800 mAH (Ni-mH)

Charging Time: 40-70 Minutes

Charging Times: 500 times

Charger Voltage Input: AC100 - 240V (50-60 Hz)

 

Package:

Unit Dimension: 277 x 100 x 290 mm

Unit Weight: 2.1 kgs

Kit Dimension: 418 x 408 x 162 mm

Gross Kit Weight: 7.1 kgs

Spool Package: 50 Spool / Carton / 21.5 kgs

Qty Per Carton: 3 pcs

Carton Dimension: 530 x 430 x 440 mm

20FCL / 40FCL: 860 pcs / 1800 pcs

 

Hand-held Automatic Rebar Tying Machine, a hand-held portable electrical tool, can knot the rebar automatically and quickly by itself. It is 5-6 times of higher efficiency than a professional worker. It is powered by a rechargeable battery which can be used alternatively and continuously during the tying working. The tying process can be completed by putting the machine jaw on the crossed rebars and then pulling the trigger only.

It greatly saves the labor cost and highly improves working efficiency, which is more helpful for you to carry out the targeted schedule as planned. It is very easy and simple to operate. Now it is more and more popular in building sites.

Before injecting the concrete during the construction of building, road, bridge, etc., ironworkers tie rebar by hand with pliers and tie wire. This work requires repeated, fast hand and arm movements while applying a lot of force. If you tie rebar at ground level, you also have to work in a stooped position with your body bent deeply forward. Tying rebar by hand greatly increases your chance of developing hand-wrist disorders due to the high hand forces used to grip pliers, the rapid hand movements used to wrap and twist wire, and the high pressure on the hand and fingers when twisting and cutting wire. If you work at ground level, you also are at risk of low back injuries from frequent and prolonged stooping and bending.

Use a Rebar Tying Machine. This lowers your risk of hand and wrist injury because it eliminates the frequent rapid hand motions required when using pliers. Some rebar tiers allow you to work standing up, so there is less stress on your low back due to stooping and bending.

Safety and health experts believe there is a risk reduction. Biomechanical research shows that high compression forces occur in the spine while stooping, and that sustained or repeated flexion of the spine may decrease the stability of the lower back and increase the risk of fatigue, leaving the back more vulnerable to injury.

While there is considerable research that shows that working in stooped, kneeling and squatting postures can cause low back disorders, the research mostly focuses on those postures in combi-nation with other risk factors such as bending or twisting or heavy loads. The literature combining stooped, squatting or kneeling postures with load handling shows rapid and severe spinal damage. There is much less in the literature regarding the health effects of these postures in an unloaded situation - that is, stooping without lifting.

However, safety and health experts believe that it is important to avoid prolonged and repeat forward bending of the back (stooping) even in the absence of the other risk factors for low back disorders. Safety and health experts believe there is an increase in productivity. Workers should experience fewer injuries. Studies conducted by NIOSH and the Construction Safety Association of Ontario (Canada) compared manual methods and one model of power tying tool, and showed that using the power tool may reduce the risk of injury to workers' hands, wrists, and low back.


We have a very strict quality controling system which promise that Rebar Tying Machine we produce are always of best quality!We also accept special order about the products. If you are interested in our products. Please do not hesitate to let us know.We are pleased to give you the detailed information.We always promise to offer excellent products as well as satisfactory service to our clients all over the world.We are sincerely looking for your cooperation.


Company information:
    Shenzhen Rhymestar Technology Co., Ltd. was found in 2009 . We is an exporter of China (Mainland) Motor products.    Our products are mainly sold to North America South America Eastern Europe Southeast Asia Africa Mid East Eastern Asia Western Europe Northern Europe! Highest quality and best price is the first to offer for our customers!    We sincerely invite you to contact us!please visit our website at www.rhyme-star.com for a full list of products.
Hot Searches: Synthetic Rubber(butadiene-styrene ,First Ranking ,??o?`???? ,?o?`???�?? ,First Rankings
 
Send Inquiry to this Supplier
 
Shenzhen Rhymestar Technology Co., Ltd.
Mr. Leo Su
Jimeihe Building, No.339, National Highway 107, Xicheng Industrial Park, Xixiang Town, Baoan District, Shenzhen, China 518126.
86-755-27889223,27889224,27889225
13922888221

Copyright © 2010 Wholesale lots. All rights reserved. Contact Us:tonyluo2005@gmail.com

Processed in 0.12069 second(s)