Cixi Deng-Hui Mould Manufacturing Co., Ltd.
 Automobiles & Motorcycles > Exterior Accessories >  Magnetic fuel saver

Magnetic fuel saver

Fuel Filter
Brand Name:
Model Number:
Magnetic fuel saver
Detailed Description

Benifits from using Powermag Fuel Saver . saver money

Benifits from using Powermag Fuel Saver

1. Up to 30% Increase in Engine Life
2. Up to 50% Reduction in Carbon monoxide and Hydrocarbon
3. Up to 10% to 22% Fuel Savings
4. Does NOT void vehicle warranty
5. Works on all vehicle including diesel
6. Save Up to $500 to $1, 500 a Year and more

7. No cutting of the fuel line
8. Up to 10 Horse Power Increase
9.0% Maintenance for Life
10. Less Than 5 Minute to Install

Guaranteed Result!


Untreated Fuel molecules tend to clump together due to attraction between molecules with charges of opposite polarities. This causes an inefficient burn. As a result, your engine experiences loss of power, lower gas mileage and lots of carbon build-up. Powermags powerful magnetic field causes these clumps of fuel molecules to be charged with a single polarity, thus they repel each other making the fuel disperse more efficiently causing more complete combustion and power production. Turbomag will actually remove the existing carbon build-up in your engine - this usually takes an average of 3 tanks full of gas, followed by a dramatic increase in gas mileage and horsepower.

Since our Powermag Fuel Saver is New in the market, we dont have any customer feedbacks on it yet but because of our success on our first generation Turbomag fuel saver we have decided to built a better and bigger model. These following testimonials from our first generation Turbomag Fuel Saver

This Auction includes

2 pieces Powermag Fuel Savers
1 Cable Ties
1 Instruction Sheet

Installing Powermag fuel saver

1. Locate the fuel supply line under pressure feeding the engine from the fuel tank. Vehicles with fuel injection engines normally have two lines running parallel between the fuel tank and the engine, a supply line and a return line. While the engine is running, feel the lines and the colder one of the two will be the supply line.

2. Insert the nylon tie through the grooves that have the tie retainer slot. This is to help hold the tie in position while applying the Powermag to the fuel line.

3. Simply place the Powermag over the fuel supply line, at the accessible location as close to the carburetor or fuel injection system as possible. However do not install the Powermag in close proximity to the alternator or any electromagnetic energy source. Installation on a metal line has given the best performance. In some cases there has been somewhat less effectiveness on plastic and rubber. We believe better radiation can be achieved through the metal; While we have had good positive results on all materials, if you can, choose a metal fuel line even if it is a connector before the carburetor etc. Do not install the device on braided metal fuel line. This should be replaced for base metal, rubber or plastic fuel pipe.

4. Align the Powermag halves so as the side grooves are alike. Complete installation by wrapping the tie completely around the Powermag making sure the tie fits into the side grooves. Trim off the excess tie. Check again whether the halves are vertically as well as horizontally alike.

Due to the cleaning and removal process of the carbon/varnish deposits inside the cylinders, the fuel consumption may temporarily increase during the initial cleaning cycle. Mileage will stabilize after a short time. Noticeable improvement may take up to four tanks of fuel and, for optimum results to be achieved, please allow 1, 000 miles or 3 full tanks of gas. A clean air filter, or a measure of carburetor or injector cleaner mixed in the fuel will also help to give faster results and regular servicing is obviously still necessary. Increased performance and smoother running will often also be noticed.

All this kind Excellent Application, we promise will offer the best price by the good quality in china!We have confidence that you will satisfy with our products and service.Our toner cartridges are high quality with low price. We promise to supply our customers best service.Above items are just a part, many more Cisco products are not listed out, please feel free contact us for more details. Thank you for your attention

Company information:
    Cixi Deng-Hui Mould Manufacturing Co., Ltd. established sine 1996 . We is an exporter of China (Mainland) Other Exterior Accessories products.    With independent export rights, our products have been exported to North America Eastern Europe Western Europe, etc. Our products have enjoyed a good reputation for our good quality, considerate service and reasonable price!    We hereby sincerely invite you and your company representatives to visit our booth!
Hot Searches: Perfume Toilet Dispenser ,Folded Towel Dispenser ,Abs Paper Dispenser ,Compact Tissue Dispenser ,Paper Roll Towel Dispenser
Send Inquiry to this Supplier
Cixi Deng-Hui Mould Manufacturing Co., Ltd.
Ms. Sisy Pan
Longchuan Road,HengHe Town Cixi City

Copyright © 2010 Wholesale lots. All rights reserved. Contact

Processed in 0.12069 second(s)